CostGuide.ca For contractors

How much does a plumber cost in Toronto?

Plumbers in Toronto and the GTA typically charge $120 to $190 an hour, according to one Mississauga company. Snaking a single sink, tub or laundry drain costs $189 to $350, and a backwater valve runs $1,440 to $2,800 before the City subsidy. Digging, cutting a finished floor and the state of old drains move the price most.

By the CostGuide.ca editorial team. Published 18 November 2026. Prices checked November 2026. The ranges are published prices from 5 contractors and suppliers, not averages. Each row names its source.

Get a quote from a local plumber

How much do common plumbing jobs cost in Toronto?

Clearing one blocked drain in Toronto costs a few hundred dollars, flood protection work such as a sump pump in an existing pit runs $1,400 to $2,400, and digging up a sewer line can reach $12,000 before restoration.

Toronto plumbing, drain and flood protection prices

Low to high range Typical

JobLowTypicalHigh
Plumber hourly rate$120 to $190per hour, one contractor's published price [1]Typical GTA rate, per a Mississauga plumbing company $120 No average published $190
Drain snaking, single fixture (kitchen, bath or laundry)$189 to $350per drain, one contractor's published price [2]A Toronto drain company's 2026 range $189 No average published $350
Toilet clog snaking (auger)$220 to $380per toilet, one contractor's published price [2]Includes a new wax ring if the toilet has to come off $220 No average published $380
Main sewer line snaking through a cleanout$350 to $650per job, one contractor's published price [2]Basement cleanout to the property line, usually 60 to 90 ft of pipe $350 No average published $650
Drain cleaning, general range$250 to $600per job, one contractor's published price [3]Typical is the guide's stated average. Excludes HST, per the source. A Toronto and GTA guide that calls these 2025 rates $250 $300 $600
Hydro jetting, 3 inch branch line$400 to $750per line, one contractor's published price [2] $400 No average published $750
Hydro jetting, 4 inch main sewer$650 to $1,400per job, one contractor's published price [2]Full main line flush, about 2 to 3 hours on site $650 No average published $1,400
Cast iron drain descaling$900 to $2,400per job, one contractor's published price [2] $900 No average published $2,400
Camera inspection after drain cleaning$250 to $400per inspection, one contractor's published price [2]Added to the cleaning price $250 No average published $400
Access charge when there is no cleanout (toilet pulled or roof vent)$150 to $300per visit, one contractor's published price [2]Added to the cleaning price $150 No average published $300
Toilet replacement, including disposal of the old unit$200 to $450per toilet, one contractor's published price [3]Excludes HST. The guide does not say whether the new toilet is included $200 No average published $450
Toilet installation, labour only$200 to $500per toilet, one contractor's published price [1]GTA figure from a Mississauga plumbing company $200 No average published $500
Backwater valve installation, before subsidy$1,440 to $2,800per valve, one contractor's published price [4]Most residential installs, per a Toronto plumber. A related guide summary on the same page gives 2,800 to 4,800 $1,440 No average published $2,800
Backwater valve installation, tile or finished floor$1,800 to $3,200per valve, one contractor's published price [4]Before subsidy $1,800 No average published $3,200
Backwater valve combined with a sump pump or other basement work$2,500 to $5,500per job, one contractor's published price [4]Not a valve only price $2,500 No average published $5,500
Primary sump pump in an existing pit$1,400 to $2,400per pump, one contractor's published price [5] $1,400 No average published $2,400
Sump pump with a new pit cut into a finished slab$2,800 to $4,500per installation, one contractor's published price [5] $2,800 No average published $4,500
Sump pump battery backup, retrofit only$1,200 to $2,400per backup, one contractor's published price [5]Added to an existing primary pump $1,200 No average published $2,400
Primary sump pump plus battery backup$3,500 to $6,500per installation, one contractor's published price [5] $3,500 No average published $6,500

Prices in CAD as local contractors publish them. Most do not say whether 13% HST is included, so ask for HST as its own line. Checked November 2026.

The figures below come from the 2026 cost pages of three Toronto area plumbing and drain companies, in Etobicoke, East York and Mississauga, each opened again in November 2026. Nothing is averaged. The East York company's guide calls its figures 2025 rates and says they exclude HST. The other two do not say whether HST is in their prices.

Two Toronto jobs come with City money or City rules attached, so this page spends extra time on them: backwater valves and sump pumps under the basement flooding subsidy, and the private side of a lead water service pipe. For the same kinds of jobs priced in another Ontario city, see the Ottawa plumbing guide, or compare five cities on the plumbing costs across Canada page.

Want a real number for your plumbing job?

What do you need?

What does it cost to replace a sewer or water line in Toronto?

A Toronto and GTA plumbing guide puts trenchless sewer repair at $4,500 to $8,000 and replacement by excavation at $5,000 to $12,000, while a Mississauga company prices a short 3/4 inch water service replacement at $2,500 to $3,800.

Toronto sewer and water service line prices

Low to high range

JobLowHigh
Trenchless sewer repair$4,500 to $8,000per home, one contractor's published price [3]Excludes HST, per the source. A Toronto and GTA guide that calls these 2025 rates $4,500 $8,000
Sewer line replacement by excavation$5,000 to $12,000per home, one contractor's published price [3]Excludes HST, per the source. A Toronto and GTA guide that calls these 2025 rates. Surface restoration is extra $5,000 $12,000
Surface restoration after sewer work (driveway, lawn, walkway)$500 to $2,500per home, one contractor's published price [3]Added to the sewer price. Depends on materials and finish. Excludes HST, per the source $500 $2,500
Water service line replacement, 3/4 inch, up to 30 ft$2,500 to $3,800per home, one contractor's published price [1]GTA figure from a Mississauga plumbing company, given for replacing lead pipe or upgrading to a larger line $2,500 $3,800
Water service line replacement, 3/4 inch, 30 to 45 ft$3,600 to $5,200per home, one contractor's published price [1]GTA figure from a Mississauga plumbing company, given for replacing lead pipe or upgrading to a larger line $3,600 $5,200
Water service line replacement, 1 inch, up to 30 ft$3,500 to $4,600per home, one contractor's published price [1]GTA figure from a Mississauga plumbing company, given for replacing lead pipe or upgrading to a larger line $3,500 $4,600
Water service line replacement, 1 inch, 30 to 45 ft$4,500 to $5,800per home, one contractor's published price [1]GTA figure from a Mississauga plumbing company, given for replacing lead pipe or upgrading to a larger line $4,500 $5,800

Prices in CAD as local contractors publish them. Most do not say whether 13% HST is included, so ask for HST as its own line. Checked November 2026.

What makes a Toronto plumbing bill go up?

Whether the plumber can reach the pipe through a cleanout, whether a floor or yard has to be opened, and the condition of old cast iron drains set most Toronto plumbing prices.

  • Snake first, jet later. A Toronto drain company says to snake first when the clog is fresh and in a single fixture, such as hair, paper or a light grease film. Hydro jetting, at $400 to $750 for a branch line, is for heavier buildup that a cable cannot shift. [2]
  • No cleanout. If there is no cleanout to reach the main line, the plumber has to pull a toilet or go in through the roof vent. The same company adds $150 to $300 for that on top of the cleaning. [2]
  • A camera after cleaning. Running a camera through the line once it is clear adds $250 to $400. The company recommends it for a drain that keeps slowing down, a line more than 30 years old or pipe of unknown material. [2]
  • Digging and putting it back. An East York plumber says excavation is the dearest way to replace a sewer line because of the digging, the longer labour hours and the restoration afterward. Rebuilding a driveway, lawn or walkway adds $500 to $2,500. The Calgary sewer line guide explains how relining and pipe bursting differ from digging. [3]
  • Pump quality. A Toronto plumber says cast iron sump pumps last 8 to 12 years and builder grade plastic pumps 3 to 5 years, so a cheaper pump may need replacing sooner. [5]

What does replacing a lead water pipe cost in Toronto?

A Mississauga company that works across the GTA prices replacing a 3/4 inch water service line, including one made of lead, at $2,500 to $3,800 for up to 30 ft, with longer and wider lines costing more.

What the price covers

The company gives the GTA ranges in the table above for replacing lead pipe or upgrading to a larger line, and its separate lead pipe section quotes a slightly different range for exterior work. Ask whether a quote covers digging to the property line, the connection at the City's side and restoring the lawn or driveway. [1]

Matching the City's side

If you commit to replacing your part of a lead pipe, you can apply to have the City replace its part on a priority basis. The City aims to finish its side within 12 weeks of approval (as at July 2026). [8]

What City programs and rules affect plumbing costs in Toronto?

Toronto pays part of the cost of backwater valves and sump pumps for eligible owners, requires a building permit for a backwater valve, and leaves the private side of a lead pipe to the owner.

How much is Toronto's basement flooding subsidy?

Up to $6,650 per property, paid toward flood protection work such as backwater valves and sump pumps (as at November 2026). The caps are up to $1,600 per backwater valve (two devices at most), up to $2,250 for one sump pump, up to $300 for a battery backup, and up to $400 for pipe severance and capping, including eligible labour, materials and taxes. [6]

Which jobs get the higher Toronto subsidy amounts?

Eligible work completed on or after November 12, 2025, with applications for the higher amounts open since May 1, 2026 (as at November 2026). Before that, the caps were $1,250 for a backwater valve and $1,750 for a sump pump. Some contractor pages still quote older figures, so check the City's page before counting on a number. [6]

Who can apply for the Toronto subsidy?

The registered owner of a single-family home, duplex, triplex or fourplex. You must apply within two years of installing each device. Funding is first come, first served and depends on what City Council approves each year (as at November 2026). [6]

Do you need a permit for a backwater valve in Toronto?

Yes. The City's subsidy page tells homeowners to get a building permit to install a backwater valve. A Toronto plumber says most installs take one day of work, and the valve must pass a City inspection before the floor is closed back up. [6] [4]

Could a Toronto home have a lead water pipe?

Yes, if it was built before the mid-1950s, according to the City (as at June 2025). The City owns the section from the watermain to the property line. The section from the property line into the house is private, and replacing it is the homeowner's cost. [7] [8]

What sales tax applies to plumbing work in Toronto?

Ontario charges a single 13% HST, according to the Canada Revenue Agency's rate table (as at November 2026). Most of the plumbing price pages behind this guide do not say whether HST is in their figures, so ask for it as its own line. [9]

What should a Toronto plumbing quote include?

A Toronto plumbing quote should say whether it is a flat price or hourly, how the plumber will reach the line, who handles the permit and inspection, what restoration is included, and HST on its own line.

  • Flat job price or hourly, and what the hourly rate covers
  • For drain jobs, whether the line is reached through a cleanout or by pulling a toilet
  • Whether a camera inspection follows the cleaning, and whether you get the video
  • For a backwater valve, who takes out the building permit and books the City inspection
  • Whether the plumber will help with the City subsidy paperwork
  • Floor, driveway or lawn restoration, included or extra
  • For sump work, the pump type and its warranty
  • HST as its own line

Plumbing terms on a Toronto quote

Cleanout
A capped access point on a drain or sewer line, often in the basement floor, that lets a plumber reach the main line without lifting a toilet. [2]
Descaling
Cutting away the rust and scale that build up inside old cast iron drain pipe so water flows freely again. [2]

Toronto plumbing questions

What will a backwater valve cost me in Toronto after the subsidy?

That depends on your invoice and the City's cap. One Toronto plumber prices most installs at $1,440 to $2,800 before any subsidy, and $1,800 to $3,200 when tile or a finished floor has to be cut. The City pays up to a set amount per valve, so check the current cap on its page before you work out your share.

Is drain snaking or hydro jetting cheaper in Toronto?

Snaking is cheaper on the published figures. One Toronto drain company charges $189 to $350 to snake a single fixture and $350 to $650 for the main line through a cleanout, against $400 to $750 to jet a branch line and $650 to $1,400 for the main sewer.

How much does a sump pump with battery backup cost in Toronto?

A primary pump with a battery backup costs $3,500 to $6,500 installed, according to a Toronto plumber, or $1,200 to $2,400 to add a backup to a pump you already have. If the basement has no pit, cutting a new one into a finished slab costs $2,800 to $4,500.

Do Toronto plumbers charge by the hour or by the job?

Both. Toronto drain companies publish flat prices per job, such as $220 to $380 to auger a clogged toilet, while a Mississauga company gives a typical hourly rate of $120 to $190. Ask which applies before work starts, and get a flat price in writing.

Do Toronto plumbing prices include HST?

Usually the sources do not say. One Toronto and GTA guide states that its figures exclude HST, and the others are silent on tax. Ontario's rate is 13%, so ask for HST as a separate line and compare quotes before tax.

Sources

  1. Plumber Cost Toronto, City Rooter Plumbing and Drain Services (Mississauga plumbing and drain company). Published 2026-08-18. Checked 2026-11-18.
  2. Drain Cleaning Cost Toronto 2026, Tornado Plumbing & Drains (Etobicoke, Toronto plumbing and drain company). Published 2026-09-15. Checked 2026-11-18.
  3. Plumbing Cost Guide for 2026 in Toronto & GTA, East York plumbing company, Toronto. Published 2026-02-05. Checked 2026-11-18.
  4. Backwater Valve Installation in Toronto & the GTA, Tornado Plumbing & Drains (Etobicoke, Toronto plumbing and drain company). Published 2026-09-04. Checked 2026-11-18.
  5. Sump Pump Installation Cost Toronto 2026, Tornado Plumbing & Drains (Etobicoke, Toronto plumbing and drain company). Published 2026-09-15. Checked 2026-11-18.
  6. Basement Flooding Protection Subsidy Program, City of Toronto. Published 2026-11-06. Checked 2026-11-18.
  7. Lead in drinking water, City of Toronto. Published 2025-06-11. Checked 2026-11-18.
  8. Priority Lead Water Service Replacement Program, City of Toronto. Published 2026-07-31. Checked 2026-11-18.
  9. GST/HST calculator (and rates), Canada Revenue Agency. Checked 2026-10-29.

Plumber hourly rate$120 to $190

Get a quote